View SP14Q003_593470.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

w
w
w
.D
at
Sh a
et e
4U
.
om c
KAOHSIUNG HITACHI ELECTRONICS CO.,LTD P.O. BOX 26-27 2,13TH EAST ST. K.E.P.Z. KAOHSIUNG TAIWAN R.O.C. TEL:(07) 8211101(10 LINE) TELEX:81903 KHE FAX:(07) 821-5860
FOR MESSRS.
DATE. Jan.24.`00 CUSTOMER'S ACCEPTANCE SPECIFICATIONS SP14Q003 CONTENTS
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 COVER
ITEM RECORD OF REVISION MECHANICAL DATA ABSOLUTE MAXIMUM RATINGS OPTICAL CHARACTERISTICS BLOCK DIAGRAM INTERFACE TIMING
7B64PS 2701-SP14Q003-1 7B64PS 2702-SP14Q003-1 7B64PS 2703-SP14Q003-1 7B64PS 2704-SP14Q003-1 7B64PS 2705-SP14Q003-1 7B64PS 2706-SP14Q003-1 7B64PS 2707-SP14Q003-1 7B64PS 2708-SP14Q003-1 7B63PS 2709-SP14Q003-1 7B64PS 2709-SP14Q003-1 7B64PS 2710-SP14Q003-1 7B64PS 2711-SP14Q003-1 7B64PS 2712-SP14Q003-1 7B64PS 2713-SP14Q003-1
ELECTRICAL CHARACTERISTICS
DIMENSIONAL OUTLINE QUALITY STANDARD
PRECAUTION IN DESIGN DESIGNATION OF LOT MARK PRECAUTION FOR USE
w
w
w
.D
t a
S a
e h
t e
SHEET No.
U 4
.c
m o
PAGE 1-1/1 2-1/1 3-1/1 4-1/1 5-1/1 6-1/2~2/2 7-1/1 8-1/3~3/3 9-1/2 9-2/2 10-1/3~3/3 11-1/3~3/3 12-1/1 13-1/1
WHEN PRODUCT WILL BE DISCONTINUED , CUSTOMER WILL BE INFORMED BY HITACHI WITH TWELVE MONTHS PRIOR ANNOUNCEMENT.
ACCEPTED BY;
PROPOSED BY;
KAOHSIUNG HITACHI ELECTRONICS CO.,LTD.
Sh. No.
7B64PS 2701-SP14Q003-1
w
w
w
.D
at
Sh a
et e
4U
.
om c
PAGE 1-1/1
RECORD OF REVISION
DATE SHEET No. SUMMARY
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2702-SP14Q003-1
PAGE 2-1/1
3. GENERAL SPECIFICATIONS
(1) PART NAME (2) MODULE SIZE (3) EFFECTIVE DISPLAY AREA (4) DOT SIZE (5) DOT PITCH (6) NUMBER OF DOTS (7) DUTY (8) LCD
SP14Q003 167.0(W)mmx109.0(H)mmx10.0 (D)mm(max.) 120 mm min. x 89 mm min 0.345(W)min. x 0.345(H)min 0.360(W)mm x 0.360(H)mm 320 (W) x 240 (H) 1/240 STN NEGATIVE MODE (BLUE) THE UPPER POLARIZER IS ANT-GLARE TYPE THE BOTTOM POLARIZER IS TRANSMISSIVE TYPE
(9) VIEWING DIRECTION (10) BACK LIGHT
6 O'CLOCK COLD CATHODE FLUORESCENT LAMP.
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2703-SP14Q003-1
PAGE 3-1/1
4. ABSOLUTE MAXIMUM RATINGS
4.1 ELECTRICAL ABSOLUTE MAXIMUM RATINGS. ITEM SYMBOL MIN. POWER SUPPLY FOR LOGIC VDD-VSS 0 POWER SUPPLY FOR LC DRIVING VDD-V0 0 INPUT VOLTAGE Vi 0.3 INPUT CURRENT Ii 0 STATIC ELECTRICITY VSS=0V:STANDARD MAX. UNIT COMMENT 6 V 27.5 V VDD+0.3 V NOTE 1 1 A 100 - NOTE 2
NOTE 1. DISP-OFF , FRAME , LOAD , CP , D0~D3. NOTE2. MAKE CERTAINS YOU ARE GROUNDED WHEN HANDLING LCM. 4.2 ENVIRONMENTAL ABSOLUTE MAXIMUM RATINGS. ITEM OPERATING STORAGE MIN. MAX. MIN. MAX. AMBIENT TEMPERATURE 0C 50C -20C 60C NOTE 5 HUMIDITY NOTE 1 NOTE 1 2 2.45m/s 11.76m/s2 VIBRATION (0.25G) (1.2G) NOTE 5 2 29.4m/s 490.0m/s2 SHOCK (3 G) (50 G) NOTE 5 CORROSIVE GAS NOT ACCEPTABLE NOT ACCEPTABLE NOTE 1 Ta<=40C : 85%RH max. Ta>40C : ABSOLUTE HUMIDITY MUST BE LOWER. THAN THE HUMIDITY OF 85% RH AT 40C NOTE 2 Ta AT 0C < 48HRS, AT 60C < 168HRS. NOTE 3 BACKGROUND COLOR CHANGES SLIGHTLY DEPENDING ON AMBIENT TEMPERATURE. THE PHENOMENON IS REVERSIBLE. HIGHER STARTING VOLTAGE OF CFL AND HIGHER LCD DRIVING VOLTAGE ARE NEEDED WHILE OPERATING AT 0C. THE FILE TIME OF CFL WILL BE REDUCED WHILE OPERATING AT 0C THIS NEED TO MAKE SURE OF VALUE OF IL AND CHARACTERICS OF INVERTER. AND THE RESPONSE TIME AT 0C WILL BE LOWER. NOTE 4 5Hz~100Hz (EXCEPT RESONALCE FREQUENCY AND X,Y,Z EACH DIRECTION WITHIN 1 HOUR) NOTE 5 THE MODULE SHOULD OPERATED NORMALLY AFTER FINISH THE TEST. Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
OMMNT NOTE 2,3 WITHOUT CONDENSATION NOTE 4
XYZ DIRECTIONS
7B64PS 2704-SP14Q003-1
PAGE 4-1/1
5. ELECTRICAL CHARACTERISTICS
5.1 ELECTRICAL CHARACTERISTICS
ITEM SYMBOL POWER SUPPLY VOLTAGE VDD-VSS FOR LOGIC POWER SUPPLY VOLTAGE VEE-VSS FOR LC DRIVING INPUT VOLTAGE VI NOTE 1 POWER SUPPLY CURRENT IDD FOR LOGIC NOTE 4 POWER SUPPLY VOLTAGE IEE FOR LC DROVING NOTE 4 RECOMMENDED LC DRIVING VOLTAGE VDD-V0 NOTE 3 FRAME FREQUENCY fFRAME CONDITION MIN. TYP. MAX. UNIT 5.0-5% 5.0 5.0+5% V -23.1 -22.0 -20.9 V V V mA mA V V V Hz
H LEVEL 0.8VDD VDD L LEVEL 0 0.2VDD VDD-VSS=5.0V 6.0 VDD-V0=-22.0V VDD-VSS=5.0V 5.0 VDD-VO=-22.0V Ta= 0C , = 0 23.5 Ta=25C , = 0 22.3 Ta=40C , = 0 21.6 70 75 80
NOTE 1 DISP-OFF , fFRAME , LOAD , CP , D0~D3. NOTE 2 RECOMMENDED LC DRIVING VOLTAGE FLUCTATE ABOUR +/-1.0V BY EACH MODULE. NOTE 3 NEED TO MAKE SURE OF FLICKING AND RIPPLING OF DISPLAY WHEN SETTING THE FRAME FREQUENCY IN YOU SET. TEST PATTERN IS ALL "Q" NOTE 4 fFRAME=75Hz , D0~D3=0,1,0,1..... VDD-V0=22.3V , Ta=25C
5.2 ELECTRICAL CHARACTERISTICS OF BACKLIGHT ITEM SYMBOL MIN. TYP. MAX. UNIT LAMP VOLTAGE VL 300 V FREQUENCY fL 70 85 kHz LAMP CURRENT IL 4 5 6 mA STARTING VS (1000) V DISCHARGE COLTAGE PLEASE CERTAINLY INFORM HITACHI BEFORE DESIGNING LAMP CIRCUIT ACCORDING TO THE ABOVE SPECIFICATIONS. NOTE Ta=25C Ta=25C Ta=25C Ta=25C DRIVE
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2705-SP14Q003-1
PAGE 5-1/1
6. OPTICAL CHARACTERISTICS
6.1 OPTICAL CHARACTERISTICS ITEM SYMBOL CONDITIONAL MIN. VIEWING AREA 2-1 K>=2.0 CONTRAST RATIO K =0 , =0 RESPONSE TIME (RISE) tr =0 , =0 RESPONSE TIME (FALL) tf =0 , =0 NOTE 1. DEFINITION OF AND (NORMAL) y(q=180) X
f2
Ta=25C(BACKLIGHT ON) TYP. MAX. UNIT NOTE 40 deg 1,2 6 3 120 ms 4 150 ms 4
(MEASURE CONDITION BY HITACHI)
NOTE 3. DEFINITION OF CONTRAST "K" K= BRIGHTNESS ON SELECTED DOT (B1) BRIGHTNESS ON NON-SELECTED DOT (B2)
(B1) ( D i= "H")
f1
X' y' q=0) (
VIE W ING DIRECTIO N
BRIGHTNESS
B1
f =10
(B2) ( D i= "L")
B2 O P E R ATING V O L T A G E
NOTE 2. DEFINITION OF VIEWING ANGLE 1 AND 2. K 2.0 1 2 CONTRAST RATIO K VS VIEWING ANGLE 1<10<2
=0
SENSOR BACKLIGHT LCD
NOTE 4. DEFINITION OF OPTICAL RESPONSE
NON-SELECTIVE STATE SELECTIVE STATE NON-SELECTIVE STATE
100% 90% tr RISE tf
10%
FALL TIME
Sh. KAOHSIUNG HITACHI DATE Jan.22.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2706-SP14Q003-1
PAGE 6-1/2
6.2 OPTICAL CHARACTERISTICS OF BACKLIGHT ITEM BRIGHTNESS RISE TIME BRIGHTNESS UNIFORMITY MIN. TYP. 110 5 -
(LCM, BACKLIGHT ON, Ta=25C) MAX. UNIT NOTE 2 cd/m IL=5mA NOTE 1,2 MINUTE IL=5mA BRIGHTNESS 80% +/-30 % UNDERMENTIONED NOTE 1,3
CFL : INITIAL, Ta=25C, VDD-V0=22.3V DISPLAY DATA SHOULD BE ALL "ON". NOTE 1. MEASUREMENT AFTER 10 MINUTES OF CFL OPERATING. NOTE 2. BRIGHTNESS CONTROL : 100% NOTE 3.MEASURE OF THE FOLLOWING 9 PLACES ON THE DISPLAY. DEFINITION OF THE BRIGHTNESS TOLERANCE.
Y=80
Y=160 Y=240
X=60 X=120 X=180
(
MAX OR MIN BRIGHTNESS - AVERAGE BRIGHTNESS AVERAGE BRIGHTNESS
)
x100%
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2706-SP14Q003-1
PAGE 6-2/2
DO~D3
IC1 Y1 Y80 Y81 Y160 Y241
IC2
IC4 Y320
7. BLOCK DIAGRAM
FRAME
LOAD X1 IC5 D3 X81 IC6 X161 IC7 X240 X240 X160 X80 D2 D1 D0 X1
Sh. KAOHSIUNG HITACHI DATE Jan.24.'99 No. ELECTRONICS CO.,LTD.
DISP-OFF
CP
320*240 DOTS
7B64PS 2707-SP14Q003-1
VDD : TIMING CIRCUIT
VSS VO
POWER SUPPLY
VEE
VCFL
PAGE 7-1/1
CFL
VCFL
8. INTERFACE TIMING CHART
8.1 INTERFACE TIMING CHART
52.1S<=T<=59.5S LOAD CP X240 D3 D2 D1 D0 M
Y1 Y5 Y2 Y6 Y3 Y7 Y4 Y8
X1
Y317
X1
Y318
Y319
Y320
FRAME
LOAD 240xT FRAME D0~D3
X1 X2
X239 X240
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2708-SP14Q003-1
PAGE 8-1/3
8.2 TIMING CHARACTERISTICS ITEM CLOCK FREQUENCY CLOCK PULSE WIDTH CLOCK RISE, FALL TIME DATA SET UP TIME DATA HOLD TIME LOAD SET UP TIME LOAD _ CLOCK TIME "FRAME" SET UP TIME "FRAME" HOLD TIME "LOAD" PULSE WIDTH SYMBOL fCP tW tr,tf tDSU tDHD tLSU tLC tSETUP tHOLD tWC 0C<=Ta=50C,VDD=5.0V+/-5% MIN. TYP. MAX. UMIT 6.5 MHz 63 ns 20 ns 50 ns 50 ns 80 ns 80 ns 100 ns 100 ns 125 ns
tw tf
0.8VDD 0.2VDD 0.8VDD 0.2VDD
tw tr
0.8VDD 0.2VDD
tw
CP
0.8VDD 0.2VDD
tDSU D0~D3
0.8VDD 0.2VDD
tDHD
0.8VDD 0.2VDD 0.8VDD 0.2VDD 0.8VDD 0.2VDD
tLSU LOAD
0.8VDD 0.2VDD 0.8VDD 0.2VDD
tLC
twc tr tSETUP
0.8VDD 0.8VDD
tf tHOLD
FRAME
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2708-SP14Q003-1
PAGE 8-2/3
8.3 TIMING OF POWER SUPPLY AND INTERFACE SIGNAL
4.75V VDD SIGNAL VEE 0~50ms GND GND GND 0 min.
5V 0~50ms
VALID DATA
4.75V GND GND GND VDD SIGNAL VEE
0 min.
0 min.
0 min.
DISP-OFF
GND POWER ON POWER OFF
GND
DISP-OFF
THE MISSING PIXELS MAY OCCUR WHEN THE LCM IS DRIVEN EXCEPT ABOVE POWER INTERFACE TIMING SEQUENCE.
8.4 POWER SUPPLY FOR LCM
VDD
+5V
LCM
VSS V0 VEE
VR -22.0V
NOTE (1) VR : 10k NOTE (2) WE RECOMMEND TO ADD FUSE (1A) TO VDD LINE. Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD. 7B64PS 2708-SP14Q003-1 PAGE 8-3/3
9.DIMENSIONAL OUTLINE 9.1DIMENSIONAL OUTLINE
167.0+/-0.5 160.0+/-0.5 4.0+/-0.3. (25.0) 1.0max. (2.4075)
7.0+/-0.5
152.0+/-0.3 (122.0) 0.36*319+0.345=115.185 7.3+/-0.5 120.0min
(200.0)
7.0+/-0.5
7.0+/-0.5
(1.3075) 1.5max. (8.5) 4.0+/-0.3
4-3.5+/-0.3
0.345 0.36
DOTS AREA EFFECTIVE AREA WINDOW OF METAL FRAME 0.36*239+0.345=86.385 89.0min (92.0) 101.0+/-0.3 109.0+/-0.5
7.0+/-0.5
0.345
0.36
(200.0)
7.0+/-0.5
CN1
7.3+/-0.5
7.0+/-0.5
(35.0) 1 14
7.5+/-0.5 1.0+/-0.2 10.0 max. (8.5 typ.)
(35.0)
0.85+/-0.2 1.25+/-0.1
STRENGTH TAPE
0.3+/-0.1 0.8+/-0.1
Kaohsiung Hitachi Sh. 7B63PS 2709-SP14Q003-1 Page 9-1/2 Jan.24.'00 Electronics Co.,Ltd. DATA No.
CONDUCTIVE SIDE
9.2 DISPLAY PATTERN 115.185 (320 DOTS)
86.385 (240 DOTS)
0.345
0.36
0.345 0.36
SCALE: NTS UNIT : mm MEASUREMENT TOLERANCE : +/-0.1
9.3 INTERFACE PIN CONNECTION INTERFACE PIN No. SIGNAL LCM I/F1 1 D0 2 D1 3 D2 4 D3 5 DISP-OFF 6 FRAME 7 N.C 8 LOAD 9 CP 10 VDD 11 VSS 12 VEE 13 V0 14 VSS PIN No. SIGNAL 1 VCFL 2 N.C 3 N.C 4 VCFL CFL I/F : J. A. E. / IL - G - 4S - S3C2 INTERFACE CFL CFL I/F
LEVEL FUNCTION H/L DISPLAY DATA
H/L H HL HL -
H : ON / L : OFF FIRST LINE MARKER DATA LATCH DATA SHIFT POWER SUPPLY FOR LOGIC GND POWER SUPPLY FOR LC OPERATING VOLTAGE LC DRIVING GND
LEVEL FUNCTION POWER SUPPLY FOR CFL CFL GND
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2709-SP14Q003-1
PAGE 9-2/2
10. APPEARANCE STANDARD
10.1 APPEARANCE INSPECTION CONDITIONS (IN THE EFFECTIVE VIEWING AREA) VISUAL INSPECTION SHOULD BE UNDER THE FOLLOWING CONDITION.
(1) IN THE DARK ROOM. (2) WITH CFL PANEL LIGHTED WITH PRESCRIBED INVERTER CIRCUIT. (3) WITH EYES 25cm DISTANCE FROM LCM. (4) VIEWING ANGLE WITHIN 45 DEGREES FROM THE VERTICAL LINE TO THE CENTER LCD.
EYE 45 LC D BEZEL 45
EYE
10.2 DEFINITION OF EACH ZONE A ZONE : WITHIN THE VIEWING AREA SPECIFIED AT PAGE 9-1/2 OF THIS DOCUMENT. B ZONE : AREA BETWEEN THE EDGE LINE OF LCD GLASS AND THE VIEWING AREALINE SPECIFIED AT PAGE 9-1/2 OF THIS DOCUMENT.
EFFECTIVE AREA EDGE LINE OF LCM A ZONE B ZONE
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2710-SP14Q003-1
PAGE 10-1/3
10.3 APPEARENCE SPECIFICATION *) IF THE PROBLEM OCCURESS ABOUT THIS ITEM, THE RESPONSIBLE PERSON OF BOTH PARTY (CUSTOMER AND HITACHI) WILL DISCUSS MORE DETAIL. No. CRITERIA A DISTINGUISHED ONE IS NOT ACCEPTABLE (TO BE JUDGED BY HITACHI LIMIT SAMPLE) DENT SAME AS ABOVE WRINKLES IN POLARIZER SAME AS ABOVE BUBBLES AVERAGE DIAMETER MAXIMUM NUMBER D(mm) ACCEPTABLE D<=0.2 IGNORE 0.2-
-
-
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2710-SP14Q003-1
PAGE 10-2/3
No.
ITEM CONTRAST IRREGULARITY (LINE) L (A PAIR OF C SCRATCH) D
CRITERIA MINIMUM LENGTH MAXIMUM SPACE L(mm) NUMBER ACCEPTABLE W<=0.25 L<=1.2 2 20mm W<=0.2 L<=1.5 3 20mm W<=0.15 L<=2.0 3 20mm W<=0.1 L<=3.0 4 20mm THE WHOLE NUMBER 6 RUBBING SCRATCH TO BE JUDGED BY HITACHI STANDARD WIDTH D(mm) CRITERIA D<=0.4 D>0.4 W<=0.2 L<2.5 W<=0.2 L>2.5 W>0.2 W<=0.1 0.1A
B
-
-
No. ITEM C DARK SPOTS, WHITE SPOTS F FOREIGN MATERIALS (SPOT) L FOREIGN MATERIALS (LINE) B / L SCRATCHES
NOTE (1) a c b
a a b a+b =D...AVERAGE DIAMETER 2 C...SALIENT (1) DEFINITION OF LENGTH L AND WIDTH W L
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2710-SP14Q003-1
PAGE 10-3/3
11. PRECAUTION IN DESIGN
11.1 LC DRIVING VOLTAGE (VEE) AND VIEWING ANGLE RANGE. SETTING VEE OUT OF THE RECOMMENDED CONDITION WILL BE A CAUSE FOR A CHANGE OF VIEWING ANGLE RANGE. 11.2 CAUTION AGAINST STATIC CHARGE AS THIS MODULE IS PROVIDED WITH C-MOS LSI, THE CARE TO TAKE SUCH A PRECAUTION AS TO GROUNDING THE OPERATOR`S BODY IS REQUIRED WHEN HANDLING IT. 11.3 POWER ON SEQUENCE INPUT SIGNALS SHOULD NOT BE APPLIED TO LCD MODULE BEFORE POWER SUPPLY VOLTAGE IS APPLIED AND REACHES TO SPECIFIED VOLTAGE (5V+/-0.5%). IF ABOVE SEQUENCE IS NOT KEPT, C-MOS LSIS OF LCD MODULES MAY BE DAMAGED DUE TO LATCH UP PROBLEM. 11.4 PACKAGING (1) NO. LEAVING PRODUCTS IS PREFERABLE IN THE PLACE OF HIGH HUMIDITY FOR A LONG PERIOD OF TIME. FOR THEIR STORAGE IN THE PLACE WHERE TEMPERATURE IS 35C OR HIGHER, SPECIAL CARE TO PREVENT THEM FROM HIGH HUMIDITY IS REQUIRED. A COMBINATION OF HIGH TEMPERATURE AND HIGH HUMIDITY MAY CAUSE THEM POLARIZATION DEGRADATION AS WELL AS BUBBLE GENERATION AND POLARIZER PEEL-OFF. PLEASE KEEP THE TEMPERATURE AND HUMIDITY WITHIN THE SPECIFIED RANGE FOR USE AND STORAGE. (2) SINCE UPPER POLARIZERS TEND TO BE EASILY DAMAGED, THEY SHOULD BE HANDLED FULL WITH CARE SO AS NOT TO GET THEM TOUCHED, PUSHED OR RUBBED. (3) AS THE ADHESIVES USED FOR ADHERING UPPER/BOTTOM POLERIZERS ARE MADE OF ORGANIC SUBSTANCES WHICH WILL BE DETERIORATED BY A CHEMICAL REACTION WITH SUCH CHEMICALS AS ACETONE, TULUENE, ETHANOLE AND ISOPROPYLALCOHOL. THE FOLLOWING SOLVENTS ARE RECOMMENDED FOR USE: NORMAL HEXANE PLEASE CONTACT US WHEN IT IS NECESSARY FOR YOU TO USE CHEMICALS. (4) LIGHTLY WIPE TO CLEAN THE DIRTY SURFACE WITH ABSORBENT COTTON WASTE OR OTHER SOFT MATERIAL LIKE CHAMOIS , SOAKED IN THE CHAMICALS RECOMMENDED WITHOUT SCRUBBING IT HARDLY. TO PREVENT THE DISPLAY SURFACE FROM DAMAGE AND KEEP THE APPEARANCE IN GOOD STATE, IT IS SUFFICIENT, IN GENERAL, TO WIPE IT WITH ABSORBENT COTTON.
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2711-SP14Q003-1
PAGE 11-1/3
(5) IMMEDIATELY WIPE OFF SALIVA OR WATER DROP ATTACHED ON THE DISPLAY AREA BECAUSE ITS LONG PERIOD ADHERANCE MAY CAUSE DEFORMATION OR FADED COLOR ON THE SPOT. (6) FOGY DEW DEPOSITED ON THE SURFACE AND CONTACT TERMINALS DUE TO COLDNESS WILL BE CAUSE FOR POLARIZER DAMAGE, STAIN AND DIRT ON PRODUCT. WHEN NECESSARY TO TAKE OUT THE PRODUCTS FORM SOME PLACE AT LOW TEMPERATURE FOR TEST, ETC. IT IS REQUIRED FOR THEM TO BE WARMED UP IN A CONTAINER ONCE AT THE TEMPERATURE HIGHER THAN THAT OF ROOM. (7) TOUCHING THE DISPLAY AREA AND CONTANT TERMINALS WITH BARE HANDS AND CONTAMINATING THEM ARE PROHIBITED, BECAUSE THE STAIN ON THE DISPLAY AREA AND POOR INSULATION BETWEEN TERMINALS ARE OFTEN CAUSED BY BEING TOUCHED BY BARE HANDS. (THERE ARE SOME COSMETICS DETRIMENTAL TO POLARIZERS.) (8) IN GENERAL THE QUALITY OF GLASS IS FRAGILE SO THAT IT TENDS TO BE CRACKED OR CHIPPED IN HANDLING, SPECIALLY ON ITS PERPHERY. BECAUSE BE CAREFUL NOT TO GIVE IT SHARP SHOCK CAUSED BY DROPPING DOWN, ETC. 11.5 CAUTION FOR HANDING THIS LCM (SP14Q001) HAS NO METAL FRAME AND FRONT BEZEL TO PROTECT TCP(TAPE CARRIER PACKAGE). TCP DRIVER IS VERY WEAK AGAINST ANY MECHANICAL STRESS. IF SUCH STRESS APPLIED, OPEN CIRCUIT OF TCP DRIVER MAY OCCUR. AND IT CAN`T BE REPAIRED. PLEASE NOTICE THAT THIS LCM SHOULD BE HANDLED WITH ENOUGH CARE AS FOLLOWS. (1) WHEN HANDLING, HOLD LCD GLASS TO AVOID DAMAGING TCP. DO NOT HOLD PCB(PRONTED CIRCUIT BOARD). (2) AFTER INCOMING INSPECTION OF THIS LCM, WHEN TAKING OFF INTERFACE CABLE, BE CAREFUL NOT TO MAKE ANY MECHANICAL STRESS TO TCP, SUCH AS BENDING AND TWISTING.
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2711-SP14Q003-1
PAGE 11-2/3
11.6 CAUTION FOR OPERATION (1) IT IS AN INDISPENSABLE CONDITION TO DRIVE LCD`S WITHIN THE SPECIFIED VOLTAGE LIMIT SINCE THE HIGHER VOLTAGE THAN THE LIMIT CAUSES THE SHORTER LCD LIFE . AN ELECTROCHEMICAL REACTION DUE TO DIRECT CURRENT CAUSES LCD'S UNDESIRABLE DETERIORATION, SO THAT THE USE OF DIRECT CURRENT DRIVER SHOULD BE AVOIDED. (2) RESPONSE TIME WILL BE EXTREMELY DELAYED AT LOWER TEMPERATURE THAN THE OPERATING TEMPERATURE RANGE AND ON THE OTHER HAND AT HIGHER TEMPERATURE LCD`S SHOW DARK BLUE COLOR IN THEM . HOWEVER THOSE PHENOMENA DO NOT MEAN MALFUNCTION OR OUT OF ORDER WITH LCD'S WHICH WILL COME BACK IN THE SPECIFIED OPERATING TEMPERATURE RANGE. (3) IF THE DISPLAY AREA IS PUSHED HARD DURING OPERATION , SOME FONT WILL BE ABNORMALLY DISPLAYED BUT IT RESUMES NORMAL CONDITION AFTER TURNING OFF ONCE. (4) A SLIGHT DEW DEPOSITING ON TERMINALS IS A CAUSE FOR ELECTROCHEMICAL REACTION RESULTING IN TERMINAL OPEN CIRCUIT. USAGE UNDER THE RELATIVE CONDITION OF 40C 50%RH OR LESS IS REQUIRED. 11.7 STORAGE IN CASE OF STORING FOR A LONG PERIOD OF TIME (FOR INSTANCE, FOR YEARS) FOR THE PURPOSE OF REPLACEMENT USE , THE FOLLOWING WAYS ARE RECOMMENDED. (1) STORAGE IN A PLOYETHYLENE BAG WITH THE OPENING SEALED SO AS NOT TO ENTER FRESH AIR OUTSIDE IN IT , AND WITH NO DESICCANT. (2) PLACING IN A DARK PLACE WHERE NEITHER EXPOSURE TO DIRECT SUNLIGHT NOR LIGHT IS, KEEPING TEMPERATURE IN THE RANGE FROM 0 DEGREE C TO 35 DEGREE. (3) STORING WITH NO TOUCH ON POLARIZER SURFACE BY ANYTHING ELSE. (IT IS RECOMMENDED TO STORE THEM AS THEY HAVE BEEN CONTAINED IN THE INNER CONTAINER AT THE TIME OF DELIVERY FROM US.) 11.8 SAFETY (1) IT IS RECOMMENDABLE TO CRASH DAMAGED OR UNNECESSARY LCDS INTO PIECES AND WASH OFF LIQUID CRYSTAL BY EITHER OF SOLVENTS SUCH AS ACETONE AND ETHANOL, WHICH SHOUD BE BURNED UP LATER. (2) WHEN ANY LIQUID LEAKED OUT OF A DAMAGED GLASS CELL COMES IN CONTACT WITH YOUR HANDS, PLEASE WASH IT OFF WELL WITH SOAP AND WATER.
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2711-SP14Q003-1
PAGE 11-3/3
12. DESIGNATION OF LOT MARK
LOT MARK LOT MARK IS CONSISTED OF 4 DIGHT NUMBER.
9
0
8
1
YEAR 1999 2000 WEEK MONTH YEAR 2001 2002 2003
FIGURE IN LOT MARK 9 0 1 2 3
NOTE 1. SOME PRODUCTS HAVE ALPHABET AT THE END OR THE FIRST. FIGURE IN LOT MARK 01 02 03 04 05 06 FIGURE IN LOT MARK 07 08 09 10 11 12 WEEK FIGURE IN (DAY IN LOT MARK CALENDAR 01~07 08~14 15~21 22~28 29~31 1 2 3 4 5
MONTH JAN. FEB. MAR. APR. MAY. JUNE.
MONTH JULY. AUG. SEPT. OCT. NOV. DEC.
LOCATION OF LOT MARK : ON THE BACK SIDE OF LCM 9081T T : MADE IN TAIWAN.
Sh. KAOHSIUNG HITACHI DATE Jan.24.'99 No. ELECTRONICS CO.,LTD.
7B64PS 2712-SP14Q003-1
PAGE 12-1/1
13. PRECAUTIPON FOR USE
(1) A LIMIT SAMPLE SHOULD BE PROVIDED BY THE BOTH PARTIES ON AN OCCASION WHEN THE BOTH PARTIES AGREED ITS NECESSITY. JUDGEMENT BY A LIMIT SAMPLE SHALL TAKE EFFECT AFTER THE LIMIT SAMPLE HAS BEEN ESTABLISHED AND CONFIRMED BY THE BOTH PARTIES. (2) ON THE FOLLOWING OCCASIONS, THE HANDLING OF THE PROBLEM SHOULD BE DECIDED THROUGH DISCUSSION AND AGREEMENT BETWEEN RESPONSIBLE PERSONS OF THE BOTH PARTIES. (1) WHEN A QUESTION IS ARISEN IN THE SPECIFICATIONS. (2) WHEN A NEW PROBLEM IS ARISEN WHICH IS NOT SPECIFIED IN THIS SPECIFICATIONS. (3) WHEN AN INSPECTION SPECIFICATIONS CHANGE OR OPERATING CONDITION CHANGE IN CUSTOMER IS REPORTED TO HITACHI, AND SOME PROBLEM IS ARISEN IN THIS SPECIFICATION DUE TO THE CHANGE. (4) WHEN A NEW PROBLEM IS ARISEN AT THE CUSTOMER`S OPERATING SET FOR SAMPLE EVALUATION IN THE CUSTOMER SITE. THE PRECAUTION THAT SHOULD BE OBSERVED WHEN HANDLING LCM HAVE BEEN EXPLAINED ABOVE. IF ANY POINTS ARE UNCLEAR OR IF YOU HAVE ANY REQUESTS , PLEASE CONTACT HITACHI.
Sh. KAOHSIUNG HITACHI DATE Jan.24.'00 No. ELECTRONICS CO.,LTD.
7B64PS 2713-SP14Q003-1
PAGE 13-1/1

▲Up To Search▲

Price & Availability of SP14Q003

	To Download SP14Q003 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .